All Courses

Course Conducted By
Md. Badeuzzamal Sarker
Instructor, Electrical Technology
Daffodil Polytechnic Institute

Course Conducted By
RUBEL HOSSEN
Instructor
Daffodil Polytechnic Institute

OBJECTIVES:
 To provide the understanding skill on Electronic Components, Electronic measuring and testing equipment.
 To provide understanding and skill on the basic concept of semiconductor junction and to identify physically a
range of semiconductor diodes.
 To develop comprehensive knowledge and skill on special diodes and devices.
 To develop the abilities to construct different rectifier circuits.
 To provide understanding of the basic concept and principle of transistor and to identify physically a range of
transistor.
 To provide understanding and skill on the basic concept of logic gates.

SHORT DESCRIPTION:

Electronic components; measuring and test equipment; color code and soldering; semiconductor; P-N junction
diode; special diodes and devices; power supply; transistor; transistor amplifier; logic gates.

Shuva Sarker
Jr. Instructor
Telecommunication Department
Daffodil Polytechnic Institute

Course Conducted by
Md. Emon Khan.
Jr. Instructor,
Daffodil Polytechnic Institute.

This Course for: Diploma in Engineering (5th Semester Civil)

AIMS
After completion of the course the students will be able to:
 Understand the construction process of arch and lintel.
 Understand the construction process of different types of floor.
 Understand the construction process of stairs.
 Understand the construction process of different types of roof.
 Understand the different finishing works in building.
 Understand the construction process of doors and windows.
 Understand the different operation and maintenance construction equipment.
 Understand the construction of bridge, culvert, canals etc.

SHORT DESCRIPTION
Arches; Lintels; Ground floors; Upper floors; Damp proofing; Termite treatment; Stairs; Roof; Pitched
roof; Plastering and pointing; Doors; Windows; Carpentry and joinery; Scaffolding; Form works, Pointing
& Varnishing, construction equipment, Building Services, Insulation, bridge/culverts and canals etc.

Course Conducted by
Md. Emon Khan
Jr.Instructor,
Daffodil Polytechnic Institute.
This Course for: Diploma in Engineering (6th Semester,Civil)

AIMS
• To provide understanding on the influence of the climatic condition of Bangladesh on its ground
water and surface water flow
• To provide understanding of recharging of underground water and ascertain its necessity in
Bangladesh.
• To enable to select a suitable source of water and method of irrigation for particular situation.
• To enable to select a suitable method of drainage for particular situation.
• To enable to select a suitable method for control of rivers and flood in Bangladesh.
• To understand rain water harvesting.

SHORT DESCRIPTION
Sources of water; Rainfall and run-off; Lifting of underground water; Storing and Recharging of
ground/rain water; Irrigation and its effect; Well irrigation; Water requirements for crops; and quality
of irrigation water; Storage reservoir; Dam and dyke; Irrigation canals; Silt deposit; Scouring; Canal
works; Drainage; River training works; Flood and flood management and flood control; Irrigation
projects in Bangladesh.

AIMS
 To be able to understand the properties of reinforced cement concrete (RCC).
 To be able to select the suitable size of reinforced concrete beams & lintels with reinforcement.
 To be able to supervise the placing of reinforcement for beams & lintel.

AIMS
• To enable to understand the behavior of incompressible fluids.
• To enable to understand the fundamentals of buoyancy.
• To enable to understand flow of liquid in closed system and in open channel.
• To assist in identifying the common measuring instruments / apparatus used in measuring the
various parameters of flowing liquid.
• To enable to applying the common measuring instruments / apparatus in measuring the various
parameters of flowing liquid.

This created by
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute

Mobile Communication Networks
This created by
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute


Concept of mobile communication and network; Cellular concept and its initial implementations; Digital
cellular mobile systems; Cordless communications systems (CT2, DECT, PACS and PHS); Mobile data
communication systems; Third generation mobile communication system; telecommunication
management network (TMN) and signaling system; concept of TDMA cellular mobile communication;
concept of CDMA cellular mobile communication; Global mobile satellite systems; Numbers and
identities for mobile communication services; performance benchmarks for mobile; Traffic engineering
and tracking system.

AIMS:
• To enable to apply the knowledge of scientific principles to problems of mechanical nature.
• To develop an understanding of mechanical properties of materials.
• To assist in applying mathematical and geometrical calculations to the analysis of statically
determinate beams.

SHORT DESCRIPTION
Mechanical properties of material; Laws of forces; Moment; Friction; Centroid and centre of gravity;
Moment of inertia; Torsion on circular shaft; Shear force and bending moment.

(69441)Television Transmission And Reception
Created by
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute

SHORT DESCRIPTION
Television system, Working principles of TV cameras, picture tube, transmitters and receivers,
Television signal, Television Signal Generation, Transmission and Propagation, Modern Television –
Transmission and Reception, Advanced Television systems and digital studio equipments, Cable
Television, teletext broadcast services, Satellite home receiving system and its networking, Video
recording & play back (VHS, Bmax, U-matic , video 2000, DV and HDV), Storage system, Television
studio and Automation and Features of remote control

(66841)Networks, Filters & Transmission Lines
Created by
Shuva Sarker
Junior Instructor
Telecommunication Technology
Daffodil Polytechnic Institute

SHORT DESCRIPTION
Network theorems, Four terminal networks; Half section network; Attenuators and filters; Transmission line; Line
constant & impedance matching; Antenna; Propagation of radio wave; Effect of earth curvature & ionosphere on
wave propagation.

Communication Engineering (26842)
Created by
Shuva Sarker
Instructor
Telecommunication Technology
Daffodil Polytechnic Institute.

SHORT DESCRIPTION
Communication networks; Modulation; Demodulation Receiver and Transmitter; Telephone system;
Digital communication; Communication switching system; Optical fiber; Satellite communication; Digital
Communication, Modem and mobile communications.

Course Conducted By
zayanta chandra
Daffodil Polytechnic Institute
This course is for: Diploma in Engineering (Civil 4th Semester)

Objectives of the Course:
• To enable in learning detail drawing of building components.
• To enable to undrstand and perform computer-aided design (AutoCAD).
• To be able to prepare a production drawing of a multi‐storied building.
• To be able to prepare detail drawing of building components.
• To be able to acquire knowledge and skill to prepare detail working drawing of a scheme.
• To be able to interpret the structural drawings of a multi‐storied building.
• To be able to prepare production drawings of multi‐storied buildings adopting CAD.

Short Description:
Computer-Aided Design (CAD) and plotting; 2D & 3D CAD commands; Multi‐storied building (CAD); Detail working drawing (CAD) of RCC column with footing; Lintel with sunshade; Retaining wall; Foundation, Beam, Slab, Staircase, ramp and lift core; Underground water reservoir; Septic tank.

Course Conducted By
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute
This Course is for: Diploma in Engineering (TCT 1st Semester)
Objectives of the Course
After completion of the course students will be able to:

Basic Telephony (1G, 2G, 3G, 4G,LTE And UMTS)
o Wireless and Cellular/Mobile Radio
o Wi-MAX, Wi-Fi, VOIP, PCS
o Local and Long-Distance Communications
o Image Communications
o Transmission Media , Media Gateway Control Protocol
o Telephone switching
o Voice over Internet Protocol (VoIP) and VoIP Gateway
o Telephony and Telegraph system, (NWD, ISD and PSTN)
o Telecommunication standardization organization
o OSI Model
o Bangladesh Telecommunication Regulatory Commission , function , Acts, mission and vision of BTRC

Course Conducted By
MD. Badeuzzamal Sarker
Instructor
Electrical Technology
Daffodil Polytechnic Institute
This Course is for: Diploma in Engineering (CMT 4th Semester)
Objectives of the Course
After completion of the course students will be able to:
You will get concept of digital electronics; Logic gates, Boolean algebra and logic simplification &Combinational logic circuits.

Course Conducted By
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute
This Course is for: Diploma in Engineering (TCT 6th Semester)
Objectives of the Course
After completion of the course students will be able to:
Introduction to Wireless communication, Modern wireless communication system, third generation(3G) wireless
network, fourth generation(4G) wireless network, cellular network, Amplitude Modulation(AM), Frequency
Modulation(FM), Linear Modulation technique, Constant envelope modulation technique, equalization, diversity
and channel coding, polarization diversity, frequency diversity, time diversity, different types of multiple access,
packet radio protocols, several types of wireless network, wireless system standard and 4th Industrial Revolutions.

Course Conducted By
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute
This Course is for: Diploma in Engineering (TCT 6th Semester)
Objectives of the Course
After completion of the course students will be able to:

Concept of Microwave, Microwave components; Wave guide; Microwave tubes; Microwave
measurements; Semiconductor microwave devices; Propagation models: Microwave antenna.

Introduction to estimating, Quantity estimation of excavating tank, road embankment, canal digging,
Steps, boundary wall, bituminous & RCC road, estimate of a single storied two-roomed building with
Verandah and double storied building, rate analysis.

Civic and Social Sciences; Individual and Society; Nation and Nationality; Citizenship; state and government; Law; Constitution Government and its organs;
public Opinion; Political Party; UNO And its organs; Scope and importance of Economics; Basic concepts of Economics- Utility, Wealth, consumption, income
wages and salary and savings; Production- meaning, nature, factors and laws; demand and supply; Current economic problems of Bangladesh; Role of Diploma
engineers in the economic development of Bangladesh; Occupations and career planning; Engineering team.

Industrial Management (65852)

* To be able to develop the working condition in the field of industrial or other organization.
* To be able to understand develop the labor management relation in the industrial sector.
* To be able to develop the management techniques in the process of decision making.
* To be able to manage the problems created by trade union.
* To be able to understand planning.
* To be able to perform the marketing.
* To able to maintain inventory.

 SHORT DESCRIPTION
Basic concept of management; Principles of management; planning, Organization, Scientific management; span of supervision; Motivation; Personal Management & human relation ; Staffing and manpower planning; Training of Staff; Concepts and techniques of decision making; Concept of Leadership; Concept of trade union; Inventory control; Economic lot size; Break even analysis; Trade Union and industrial dispute, Marketing.

Course Conducted By
Shuva Sarker
Jr. Instructor
Telecommunication Technology
Daffodil Polytechnic Institute
This Course is for: Diploma in Engineering (TCT 4th Semester)
Objectives of the Course
After completion of the course students will be able to:
This is a sector specific course of diploma in engineering program required for enabling the
graduates to use and work with ICT. It includes Concept of digital electronics, Number system
and binary arithmetic operation, Arithmetic codes and code conversion, Concept of logic gates,
Electronic circuit of logic gates, Digital ic’s Logic families, Logic simplification & circuit design,
Combinational logic circuits, Encoder and decoder, Multiplexers and DE-Multiplexer, Sequential
logic circuits. This course designed emphasis will be more on teaching practical aspect rather
than theory.

Offset machine operation is a critical process in the printing industry, involving several meticulous steps to ensure high-quality results. Initially, the machine is prepared by collecting job information and setting up the machine according to this data. The inking unit is controlled by measuring pH levels, roller hardness, and adjusting the roller gap to regulate ink supply. The feeding unit is then prepared by setting the sucker and blower, adjusting guides, and maintaining the feed board height. Sheet control involves setting various lays, measuring paper thickness, and adjusting the double sheet detector. Plates and blankets are cleaned, prepared, and preserved to ensure quality. During the printing process, the press is made ready, run for production, and cleaned as needed, with strict control over print registration for multi-color jobs. Safety measures are followed meticulously, raw materials are handled carefully, and management plays a crucial role in accident prevention. Finally, the delivery unit is set up by adjusting guides and maintaining the delivery chain gripper. Detailed record-keeping throughout these steps is essential for consistent and high-quality printing outcomes.

Image Carrier preparation refers to the processes and techniques involved in creating the medium on which images will be printed using various printing technologies. The preparation process varies depending on the type of printing method being used, such as relief printing, planographic printing, intaglio printing, and screen printing. Each method requires specific materials, tools, and steps to ensure the quality and accuracy of the printed image.

### Types of Image Carriers and Their Preparation

1. Conventional Relief Printing:
involves preparing block and type forms.
uses materials like rubber and photopolymer plates.
Processes include making line blocks and half-tone blocks and handling photopolymer and rubber plates.

2. Modern Relief Printing:
utilizes digital flexo plates and various digital imaging technologies.
involves the use of digital imagers (DI) and different types of lasers for plate making.

3. Conventional Planographic Printing:
uses lithographic plates and involves the photomechanical process.
requires materials like Ps plates and involves graining processes to prepare the plate surface.

4. Modern Planographic Printing:
employs Employs Computer-to-Plate (CtP) technology and various digital imaging techniques.
includes auto plate exposure, processing of digitally imaged plates, and maintenance of image and non-image areas.

5. Intaglio Printing:
involves materials and equipment for gravure image preparation.
Processes include electroplating gravure cylinders, etching, and engraving.

6. Screen Printing:
utilizes raw materials, tools, and equipment for stencil making.
Methods include direct and indirect stencil making and Computer-to-Screen (CtS) processes.

### Learning Outcomes

**Theoretical:**
Understand image preparation processes for different printing technologies.
Differentiate between various types of image carriers.
Know the raw materials and chemicals used in image preparation.
Solve problems related to image preparation using different printing methods.

**Practical:**
Apply the tools and equipment used in screen printing.
Prepare various types of stencils and print on different substrates.
Operate screen-printing machines and presses.

These processes are essential for ensuring high-quality prints in various printing applications, from commercial printing to specialized artistic productions】.