All Courses

Course Conducted by
Md. Emon Khan.
Jr. Instructor,
Daffodil Polytechnic Institute.

This Course for: Diploma in Engineering (5th Semester Civil)

AIMS
After completion of the course the students will be able to:
 Understand the construction process of arch and lintel.
 Understand the construction process of different types of floor.
 Understand the construction process of stairs.
 Understand the construction process of different types of roof.
 Understand the different finishing works in building.
 Understand the construction process of doors and windows.
 Understand the different operation and maintenance construction equipment.
 Understand the construction of bridge, culvert, canals etc.

SHORT DESCRIPTION
Arches; Lintels; Ground floors; Upper floors; Damp proofing; Termite treatment; Stairs; Roof; Pitched
roof; Plastering and pointing; Doors; Windows; Carpentry and joinery; Scaffolding; Form works, Pointing
& Varnishing, construction equipment, Building Services, Insulation, bridge/culverts and canals etc.

Course Conducted by
Md. Zahidul Islam
Jr. Instructor,
Daffodil Polytechnic Institute.
This Course for: Diploma in Engineering (5th Semester,Civil)

AIMS
 To be able to set out different types of curve.
 To be able to conduct sounding.
 To be able to learn using total station,
 To be able to perform city survey.

SHORT DESCRIPTION
Curve ranging; Setting out Plan/alignment; Hydrographic survey; Total station; City survey.

Course Conducted by
Uchingla Marma
Instructor,
Daffodil Polytechnic Institute.
This Course for: Diploma in Engineering (5th Semester,Civil)

AIMS
 To enable to select suitable methods for collection and distribution of water from given source to
given community.
 To enable to identify impurities of water of given sources and selected suitable method/methods of
purification up to potable standard.
 To assist in comparing various types of water pipes and pipe fittings.
 To develop understanding of the procedure of construction, repair, replacement and maintenance
of water supply systems.
 To provide understanding of the socio-economic aspect of water supply and sanitation (WSS).

SHORT DESCRIPTION
Introduction; Water requirements; Sources of water; Water pipes; Collection and transmission of water;
Quality of water; Treatment of water (clarification); Treatment of water (filtration); Treatment of water
(disinfection and softening); Miscellaneous water treatment; Water distribution; Water reservoir;
Distribution system; Rural water supply system; Plumbing system.

Course Conducted by
Md. Emon Khan
Jr.Instructor,
Daffodil Polytechnic Institute.
This Course for: Diploma in Engineering (6th Semester,Civil)

AIMS
• To provide understanding on the influence of the climatic condition of Bangladesh on its ground
water and surface water flow
• To provide understanding of recharging of underground water and ascertain its necessity in
Bangladesh.
• To enable to select a suitable source of water and method of irrigation for particular situation.
• To enable to select a suitable method of drainage for particular situation.
• To enable to select a suitable method for control of rivers and flood in Bangladesh.
• To understand rain water harvesting.

SHORT DESCRIPTION
Sources of water; Rainfall and run-off; Lifting of underground water; Storing and Recharging of
ground/rain water; Irrigation and its effect; Well irrigation; Water requirements for crops; and quality
of irrigation water; Storage reservoir; Dam and dyke; Irrigation canals; Silt deposit; Scouring; Canal
works; Drainage; River training works; Flood and flood management and flood control; Irrigation
projects in Bangladesh.

Subject Teacher : Md. Zahidul Isam, Jr. Instructor
Subject Name : Theory of Structure
Subject Code : 66454
Technology : Architecture
Semester :6th

AIMS
• To be able to consolidate and extend the fundamental understanding of the behavior of statically
determinate structures i.e. beams, frames etc.
• To be able to develop of awareness of structural behavior such as deflection and stability of
masonry dam.
• To be able to develop understanding for selection of suitable section of beam and member of the
truss.
SHORT DESCRIPTION
Shear force and bending moment of beams; Stresses in beams; Deflection of beams; Joints and
connections; Forces in frames; Steel structure; Masonry dam; Column; Moving loads; Thin Cylindrical
shells.

AIMS
 To be able to understand the foundation and foundation engineering.
 To be able to understand the soil stabilization.
 To be able to understand and the bearing capacity of soil.
 To be able to understand the factors determining types of foundation.
 To be able to understand the foundation on sand and non-plastic soil, plastic soil, non-uniform soil,
rock.
 To be able to understand the excavating and bracing.
 To be able to understand the sheet pile wall, cofferdam and bulk head.
 To be able to understand the damages due to construction operations.

SHORT DESCRIPTION
Foundation and foundation engineering; Factors determining the types of foundation; Soil stabilization;
Bearing capacity of soil; Foundation on sand and non-plastic silt; Foundation on clay and plastic silt;
Foundation on non-uniform soil; Foundation on rock; Excavation and bracing; Sheet pile, cofferdam &
bulkhead; Damages due to construction operations.

To provide a foundation in scientific principals and processes for the understanding and application of technology. It will help our students to make a common base for further studies in technology and science. It also help to develop the basic knowledge of modern physics.

Offset machine operation is a critical process in the printing industry, involving several meticulous steps to ensure high-quality results. Initially, the machine is prepared by collecting job information and setting up the machine according to this data. The inking unit is controlled by measuring pH levels, roller hardness, and adjusting the roller gap to regulate ink supply. The feeding unit is then prepared by setting the sucker and blower, adjusting guides, and maintaining the feed board height. Sheet control involves setting various lays, measuring paper thickness, and adjusting the double sheet detector. Plates and blankets are cleaned, prepared, and preserved to ensure quality. During the printing process, the press is made ready, run for production, and cleaned as needed, with strict control over print registration for multi-color jobs. Safety measures are followed meticulously, raw materials are handled carefully, and management plays a crucial role in accident prevention. Finally, the delivery unit is set up by adjusting guides and maintaining the delivery chain gripper. Detailed record-keeping throughout these steps is essential for consistent and high-quality printing outcomes.

Image Carrier preparation refers to the processes and techniques involved in creating the medium on which images will be printed using various printing technologies. The preparation process varies depending on the type of printing method being used, such as relief printing, planographic printing, intaglio printing, and screen printing. Each method requires specific materials, tools, and steps to ensure the quality and accuracy of the printed image.

### Types of Image Carriers and Their Preparation

1. Conventional Relief Printing:
involves preparing block and type forms.
uses materials like rubber and photopolymer plates.
Processes include making line blocks and half-tone blocks and handling photopolymer and rubber plates.

2. Modern Relief Printing:
utilizes digital flexo plates and various digital imaging technologies.
involves the use of digital imagers (DI) and different types of lasers for plate making.

3. Conventional Planographic Printing:
uses lithographic plates and involves the photomechanical process.
requires materials like Ps plates and involves graining processes to prepare the plate surface.

4. Modern Planographic Printing:
employs Employs Computer-to-Plate (CtP) technology and various digital imaging techniques.
includes auto plate exposure, processing of digitally imaged plates, and maintenance of image and non-image areas.

5. Intaglio Printing:
involves materials and equipment for gravure image preparation.
Processes include electroplating gravure cylinders, etching, and engraving.

6. Screen Printing:
utilizes raw materials, tools, and equipment for stencil making.
Methods include direct and indirect stencil making and Computer-to-Screen (CtS) processes.

### Learning Outcomes

**Theoretical:**
Understand image preparation processes for different printing technologies.
Differentiate between various types of image carriers.
Know the raw materials and chemicals used in image preparation.
Solve problems related to image preparation using different printing methods.

**Practical:**
Apply the tools and equipment used in screen printing.
Prepare various types of stencils and print on different substrates.
Operate screen-printing machines and presses.

These processes are essential for ensuring high-quality prints in various printing applications, from commercial printing to specialized artistic productions】.